All Categories

Get a Free Quote

Our representative will contact you soon.
Email
Name
WhatsApp
Company Name
Message
0/1000
laser cutting cost per part how to build the calculation yourself-1

News

Home >  News/Blogs >  News

Laser Cutting Cost per Part: How to Build the Calculation Yourself

Nov 09, 2026

Laser Cutting Cost per Part: How to Build the Calculation Yourself

Everyone Quotes the Machine. Almost Nobody Quotes the Part.

Ask a supplier what a machine costs and you will get a number within a day. Ask what a part costs on that machine, in your shop, with your labour and your volumes, and the answer usually arrives as a slide showing "low running cost".

That gap is where most bad laser investments are made. The purchase decision is nearly always framed as a machine price comparison, when the thing that actually determines whether the investment works is the cost per part at your real utilisation — and that number depends far more on your operation than on the machine's specification.

This article does not give prices. Any figure printed here would be wrong for most readers, because wages, power, floor space and material costs vary enormously between markets. What it gives is the structure: which buckets to fill, where to get each figure honestly, and which parts of the arithmetic people habitually get wrong.

The Seven Cost Buckets

A cost per part is a sum of seven things. Most quotations include two or three of them.

Bucket What belongs in it Where to get your own figure
1. Machine Purchase, freight, installation, financing cost, depreciation period Your invoice, and a depreciation period you can defend
2. Space Floor area occupied, including access and material storage Your rent or mortgage per square metre
3. Power Machine draw plus chiller, compressor, extraction Meter it for a week; do not use the nameplate
4. Labour Loading, unloading, nesting, inspection, finishing Your real hourly cost, including on-costs
5. Consumables Lens, mirrors, tube, nozzle, extraction filters, assist gas Your maintenance log, averaged over a year
6. Yield Material bought versus material sold, plus scrap and rework Your nesting records and reject rate
7. Overhead Software, insurance, training, supervision, rework admin Your accounts, apportioned honestly

Three of these are routinely omitted and each one changes the answer materially.

Space is almost always left out because it feels like a sunk cost. It is not: a machine that occupies floor area in a city workshop is consuming something with a market price, and the second machine always costs more space than the first because the material and offcut storage grows with it.

Consumables are usually estimated from the biggest item only — the tube — and ignore optics, nozzles and filters. Filters in particular are a recurring cost that scales with how much material is processed, not with machine hours, and shops cutting foam or coated board replace them far more often than they expect.

Yield is the bucket that separates a shop that understands its own business from one that does not. Material is usually the largest single cost in laser work, and the difference between a good nest and a careless one on the same job is a real percentage of the part cost. The kerf and nesting guide covers the geometry; this article only insists that the number be measured rather than assumed.

Why Machine-Hour Rate Fails in High-Mix Work

The standard formula is: cost per part = machine-hour rate × hours per part + material per part.

It is a good formula for a factory running one product for months. It is misleading in the work most laser shops actually do, for one reason: setup is not proportional to cutting time.

Consider two jobs on the same machine:

  • Job A: one hundred identical parts, one setup.
  • Job B: ten different parts, ten setups, same total cutting time.

The machine-hour rate attributes the same cost to both, because it only counts cutting hours. But Job B consumed ten times the loading, nesting, alignment, test-cutting and inspection. If the shop prices both with the same rate, Job B is being sold at a loss — and it is usually the job that felt like more work, which is the shop's instinct telling the truth while the spreadsheet disagrees.

The practical fix is to cost by order, then divide:

Cost element Job A (one part, 100 off) Job B (10 parts, 10 off)
Setup and programming Once Ten times
Cutting time Proportional to parts Proportional to parts
Handling One batch Ten batches
Inspection Sample Ten first-articles
Cost per part Setup amortised over 100 Setup amortised over 10

This is the single most useful change most shops can make to their pricing: add a setup charge per order line, priced from the actual time it takes, and then let the machine rate cover only running time. The result is that small, varied orders are priced honestly instead of being subsidised by the long runs — which is also why so many shops feel busy and unprofitable at the same time.

Utilisation: The Variable That Decides Payback

The buckets above are fixed and variable, and the fixed ones are spread over however many hours the machine actually runs. That makes utilisation the most powerful number in the whole calculation — and the one most often assumed rather than measured.

The arithmetic is simple and worth stating plainly: fixed cost per hour = annual fixed cost ÷ annual machine hours. Cut the hours to a third and the fixed cost per hour roughly triples. Nothing about the machine changed; only how much work passed through it.

Utilisation scenario What it looks like Effect on fixed cost per part
One shift, partly loaded Machine idle between jobs Highest
One shift, well loaded Work queued, little idle time Moderate
Two shifts Same fixed cost, more hours Roughly halved
Around the clock, lightly attended Loading by one operator, cutting overnight Lowest per hour, but labour and monitoring change

Two honest cautions about chasing utilisation.

Idle capacity is not free capacity. A machine sitting idle still consumes space, depreciation and insurance. A shop that buys capacity "for growth" and runs it at a fifth of its hours is paying the full fixed cost for a fifth of the output — which is exactly how a machine that looked affordable becomes the reason a business cannot invest in anything else.

The second shift is usually the cheapest capacity available, because the fixed cost is already paid. Before buying a second machine, the honest calculation is whether the first one can be loaded further — and often the constraint is not the machine but the operator, the finishing bench, or the customer's lead time expectations.

Payback, Stated Properly

Payback is usually presented as "machine price ÷ monthly saving". That version hides three things and flatters almost every proposal.

A defensible payback calculation has this shape:

Annual cost of the investment = depreciation + interest or financing cost + space + power + consumables + maintenance + insurance + the labour added to run it.

Annual benefit = what you no longer pay someone else, plus what you can now sell that you previously could not, minus the material and labour you now consume doing it in-house.

Payback period = annual cost of the investment ÷ annual net benefit.

Three corrections that change the answer:

Compare against the real alternative, not against zero. If the work is currently outsourced, the benefit is the outsourced invoice minus your in-house cost — not the full invoice. If the work is currently not being done at all, the benefit is speculative and should be labelled as such.

Include the labour you are adding. A machine that replaces an outsourced invoice but requires a full-time operator may be neutral, and a proposal that omits the operator is not a calculation, it is a hope.

Use the volume you can actually sell, not the machine's capacity. Capacity-based payback is the most common error in equipment proposals: it assumes the machine runs at its ceiling from month one, which almost no shop achieves.

The Costs That Never Appear in a Quotation

A list worth taking to any negotiation, because each of these is real and each is usually discovered after installation.

Item Why it is forgotten How to size it
Extraction and filtration Seen as an accessory Size for the dirtiest material you will cut
Compressor and air drying Assist air is assumed Air quality affects lens life directly
Chiller or cooling Sometimes included, sometimes not Match to the actual duty cycle
Spare lens and mirrors Treated as repair, not consumable Keep one spare set; track replacement intervals
Tube replacement interval Quoted as years, experienced as hours Ask existing users in your material mix
Floor preparation and power supply Site work, not machine work Get a quote before signing
Software and nesting Often bundled, sometimes not Confirm what is included and what is licensed
Training and the learning curve Assumed to be a day Budget for weeks of slower output
Insurance and compliance Depends on local rules Ask your insurer before installation

The learning curve deserves its own line. A new machine in an existing shop does not reach its expected output on the first day; the first weeks produce scrap, slower nesting and more questions. A payback model that starts at full productivity is wrong by exactly that ramp — and the ramp is longer for shops new to the process than for shops adding capacity.

A Structure You Can Fill In

The point of this article is not to hand over a number but to make the calculation unavoidable. The table below is the minimum honest structure; fill the right-hand column from your own records, not from a supplier's presentation.

Line What to enter Source
Machine cost, delivered and installed Total Invoice
Depreciation period Years you will actually keep it Your judgement, stated
Annual fixed cost Depreciation + financing + space + insurance Accounts
Annual machine hours Realistic, at your actual utilisation Your schedule, not the capacity
Fixed cost per hour Annual fixed ÷ annual hours Arithmetic
Variable cost per hour Power + consumables + maintenance Metering and logs
Material cost per part Including measured yield Nesting records
Labour per part Including setup amortised over the batch Time study
Cost per part Sum of the above per part Arithmetic
Selling price What the market pays Your order book
Margin per part Price minus cost Arithmetic
Annual volume What you can sell Your pipeline
Annual contribution Margin × volume Arithmetic
Payback Investment ÷ annual contribution Arithmetic

If a proposal cannot be filled into this structure with your own figures, it is not a business case yet — it is a quotation.

The Decisions This Calculation Actually Informs

Once the arithmetic exists, four decisions become answerable, and each has a different answer depending on the numbers.

Outsource or buy? Below a certain volume, outsourcing wins because you avoid the fixed cost entirely. Above it, in-house wins because the fixed cost is spread thinner. The crossover depends on your volumes and your local outsource price — which is why no article can give it to you.

Buy now or buy bigger later? A smaller machine with high utilisation usually beats a larger one running at a fraction of its hours. The exception is work that physically does not fit, where the decision is capability, not cost.

One shift or two? The second shift is normally the highest-return capacity decision available, because the fixed cost is already paid. The constraint is usually finishing capacity or operator availability, not the machine.

Add a second machine or a second process? If the bottleneck is cutting, a second cutter helps. If the bottleneck is finishing, edge banding, or assembly, a second cutter just builds a bigger queue in front of the same bottleneck. Costing the whole line, not the machine, is what prevents that mistake.

Common Costing Mistakes

Mistake What it produces Correction
Using the machine-hour rate for high-mix work Small orders sold at a loss Add a setup charge per order line
Assuming full utilisation Payback that never arrives Use your real, measured hours
Comparing machine price only Choosing the cheaper machine that costs more to run Compare cost per part at your volume
Ignoring material yield Understating the largest cost Measure nesting efficiency
Omitting the operator A proposal that is neutral in reality Include the labour added
Treating consumables as repairs Surprise costs in year two Average the maintenance log
Sizing extraction for the average material Fume problems, filter cost, downtime Size for the worst material
Starting the model at full productivity Missing the ramp Budget the learning curve
Costing the machine, not the line A bottleneck moved, not removed Cost the downstream process too

Conclusion

A laser is not cheap or expensive in the abstract; it is cheap or expensive per part, at your utilisation, in your material mix. The only way to know which is to build the arithmetic yourself — seven buckets, an honest hour count, and a setup charge that reflects what small orders actually consume.

Suppliers who resist that conversation are telling you something useful. A supplier who will sit down with your numbers, including the ones that make their machine look less attractive, is the one worth buying from — because the machine will still be in your shop long after the quotation has been filed.

The calculation is not complicated. It is just uncomfortable, because it forces the two questions most purchase decisions avoid: how much will this machine actually run, and what will I stop paying someone else to do?

laser cutting cost per part how to build the calculation yourself-2

Get a Free Quote

Our representative will contact you soon.
Email
Name
WhatsApp
Company Name
Message
0/1000